PLUMBING ESSENTIALS: A PREREQUISITE FOR INSTALLING A BATHTUB

Plumbing Essentials: A Prerequisite for Installing a Bathtub

Plumbing Essentials: A Prerequisite for Installing a Bathtub

Blog Article

Source This Article

Almost everyone has got their personal assumption in relation to How to Install a Bathtub.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Mounting a bathtub isn't specifically brain surgery, however it does require strong plumbing, woodworking, and occasionally, tiling abilities. Changing an old bathtub with a new one is likewise a moderately challenging task. If the old tub is easily available, the task can move quickly; if you need to open up a wall to get rid of the old bathtub and position the brand-new bath tub, the job is much harder. In either situation, the project is within a home handyman's skills, although you will certainly require an assistant to move out the old tub and set in the new one. Ensure you have qualified yourself for the task and fit attempting it. Rather than employing a service provider to take control of a halfway-completed task, it is better to consider employing one prior to you start. Chances are you might need an expert plumber to make tube connections.
This post will certainly aid you mount a brand-new tub in your bathroom if you have already purchased a new tub as well as don't need to alter the arrangement of your previous water pipelines.
Your devices and also product checklist should comprise the following:
  • New Tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipe Caps


  • Getting ready for the Setup


    First of all, the sustaining frame supplied with the bath must be fitted (if needed) according to the supplier's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to make sure that if the faucet comes with a plastic washer, it is fitted in between the bath and also the taps. On a plastic bath, it is likewise sensible to fit a supporting plate under the faucets unit to prevent strain on the bath tub.
    Fit the flexible tap adapters to the bottom of both faucets using 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you make use of all of the provided washers.
    Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath must currently prepare to be suited its last placement.

    Removing Old Touches


    If you require to change old taps with brand-new ones as a part of your installment, after that the first thing you must do is disconnect the water. After doing so, activate the taps to drain any water remaining in the system. The process of getting rid of the existing taps can be rather problematic because of the restricted access that is commonly the situation.
    Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipelines have actually been gotten rid of, utilize the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. Once the taps have been removed, the holes in the bath/basin will need to be cleaned of any old securing compound.
    Prior to carrying on to fit the brand-new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.

    Installing the Bathtub


    Utilizing the two wooden boards under its feet, position the tub in the required position. The wood boards are practical in evenly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto four tiny points.
    The next goal is to ensure that the bath tub is leveled all round. This can be attained by inspecting the level and changing the feet on the bathtub until the spirit level checks out level.
    To mount faucets, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the very same for the other tap.
    Activate the water supply and examine all joints and also brand-new pipework for leaks and tighten them if essential. Fill the tub and additionally inspect the overflow electrical outlet as well as the normal outlet for leaks.
    Finally, take care of the bathroom paneling as explained in the maker's instruction manual. Tiling as well as securing around the tub needs to wait until the tub has actually been utilized at the very least when as this will certainly resolve it right into its last position.

    Fitting New Touches


    If the tails of the brand-new faucets are plastic, then you will need a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end gives a link to the current supply pipelines.
    If you need to fit a monobloc, then you will certainly need decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
    Next, position the faucet in the installing opening in the bath/basin making certain that the washing machines are in area in between the tap and the sink. Secure the faucet in position with the producer given backnut. Once the faucet is securely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular faucet adapters. The former kind should be linked to the tap ends initially, tightening up just by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.

    Tiling Around the Bath tub


    In the location where the bath meets the tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break a rigid seal, triggering the water to permeate the wall between the bathroom and the tiling, leading to issues with dampness and also feasible leakages to the ceiling below.
    You can pick from a range of coloured sealants to assimilate your components as well as installations. They are marketed in tubes and cartridges, as well as are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill the bathtub with water before sealing, to allow for the movement experienced when the tub remains in usage. The sealant can break relatively early if you do not take into account this activity before securing.
    Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise quickly offered on the market. It is a good idea to fit the tiles utilizing waterproof or water resistant glue and also cement.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    Tools You Need to Install a New Bathtub

    Do you like reading up on How to Install a Bathtub? Create a comment down below. We would be delighted to listen to your ideas about this blog. Hoping that you visit us again before long. Appreciated our blog posting? Please share it. Let another person discover it. Thanks for your time. Come back soon.


    Secure timely emergency plumbing assistance.

    Report this page